This is the README for wwwcount.2.3.NIHS.bs.tar.gz [Download] [Browse] [Up]
wwwcount.2.3 compiled quad fat for NeXTSTEP by Panagiotis Velissariou.
Since I haven't see version 2.3 in the archives and since I am using it
on my NeXTstation and on SGI for quit some time now I just recompiled
it and submitted to the archives.
Compilation and installation of this program is easy (just follow the
steps below)
This is Muhammad A Muquit's Count 2.3 program, a CGI program to keep record
of the raw hits of a web page.
The official homepage of Count is moved to :
http://www.fccc.edu/users/muquit/Count.html
submitted to : ftp://next-ftp.peak.org/pub/next/submissions/wwcount.2.3.tar.gz
and probably will move to :
ftp://next-ftp.peak.org/pub/next/apps/internet/www/wwcount.2.3.tar.gz
Panagiotis Velissariou
e-mail : takis@superior.eng.ohio-state.edu
takis@takis2.ee.net
pvelissa@postbox.acs.ohio-state.edu
----------------------------------------------------------------------
Steps required to install the wwwcount.2.3 binaries
---------------------------------------------------
The defaults compiled in the binary Count.cgi are :
cgi-bin direrctory [/usr/local/etc/httpd/cgi-bin]
Base directory [/usr/local/etc/httpd/Counter]
Config directory [/usr/local/etc/httpd/Counter/conf]
configuration file [sample.conf]
Data directory [/usr/local/etc/httpd/Counter/data]
Log directory [/usr/local/etc/httpd/Counter/Log]
Name of the log file [sample.log]
If you need to change any or all of the above defaults
go to the next section "Steps required to compile and install
wwwcount.2.3"
Otherwise do the following to install Count.cgi and supporting
files in your system :
1) Run :
./Gen-conf
To generate the configuration file
Please answer all the questions (straight forward) and rename the
resulting file count.cfg to sample.conf.
2) Edit the sample.conf file to suit your needs
3) Run :
./Count-install
To install the Count.cgi and all the supporting files in your
system.
4) Edit first line the file /usr/local/etc/httpd/Counter/data/sample.dat
such that it reads 1 instead of 0
5) Read the documentation in the docs directory of how to use
Count.cgi in your web pages.
Steps required to compile and install wwwcount.2.3
--------------------------------------------------
1) Go to wwwcount.2.3 source directory and run :
./Count-config
and answer all the questions (straight forward)
These are the defaults I used to compile wwwcount.
cgi-bin direrctory [/usr/local/etc/httpd/cgi-bin]
Base directory [/usr/local/etc/httpd/Counter]
Config directory [/usr/local/etc/httpd/Counter/conf]
configuration file [sample.conf]
Data directory [/usr/local/etc/httpd/Counter/data]
Log directory [/usr/local/etc/httpd/Counter/Log]
Name of the log file [sample.log]
2) Run :
./configure
This will check your system and create the Makefiles.
3) Go end review/edit if neccessary the :
Makefile, combine/Makefile and utils/Makefile
files to suit your needs.
OR use the Makefile.NeXT in each directory
I included
"-O2 -pipe -arch hppa -arch i386 -arch m68k -arch sparc -no-precomp"
in CFLAGS
4) Run :
make
This will create the binaries
5) Run :
./Gen-conf
To generate the configuration file
Please answer all the questions (straight forward) and rename the
resulting file count.cfg to sample.conf or whatever name you used
in (1) above
6) Edit the sample.conf file to suit your needs
7) Run :
./Count-install
To install the Count.cgi and all the supporting files in your
system.
8) Edit first line the file /usr/local/etc/httpd/Counter/data/sample.dat
such that it reads 1 instead of 0
9) Read the documentation in the docs directory of how to use
Count.cgi in your web pages.
These are the contents of the former NiCE NeXT User Group NeXTSTEP/OpenStep software archive, currently hosted by Netfuture.ch.