This is qcr.h in view mode; [Download] [Up]
#include <errno.h> #include <fcntl.h> #include <stdio.h> #define RED 0 #define GREEN 1 #define BLUE 2 extern int errno; /* Command defs for QCR-Z Film Recorder */ /* These are for 8 bit Look Up Tables */ #define LUT_LOAD 0x00 #define LUT_VERIFY 0x01 #define NEUTRAL_LUT 0x1d #define NEUTRAL_VERIFY 0x1e /* These commands are for the 12 bit LUTs */ #define LOAD_12_LUT 0x4c #define VERIFY_12 0x4e #define LOAD_12_NEUTRAL 0x4d #define VERIFY_12_NEUTRAL 0x4f /* Start a color image recording, reading Red, Blue than Green */ #define THREE_PASS_PIXEL 0x06 /* For a three pass RLE image */ #define THREE_PASS_RLE 0x16 /* These are for single passes of data, fully specified (Non-RLE) */ #define NEUTRAL_PIXEL 0x02 #define RED_PIXEL 0x03 #define GREEN_PIXEL 0x04 #define BLUE_PIXEL 0x05 /* These are for single passes of data, run length format */ #define NEUTRAL_RLE 0x12 #define RED_RLE 0x13 #define GREEN_RLE 0x14 #define BLUE_RLE 0x15 #define TEST_PAT_0 0x0a #define TEST_PAT_1 0x0b #define SET_LINE_DELAY 0x0c #define GET_VERSION_ID 0x0d #define IDLENGTH 14 #define SET_DIMENSIONS 0x0e #define MIRROR_DISABLE 0x30 #define MIRROR_ENABLE 0x31 #define WARBLE_DISABLE 0x21 #define WARBLE_ENABLE 0x22 #define RED_REPEAT_ON 0x39 #define RED_REPEAT_OFF 0x38 #define AUTO_SHUTTER_OFF 0x0f #define AUTO_SHUTTER_ON 0x10 #define AUTO_FILTER_OFF 0x18 #define AUTO_FILTER_ON 0x19 #define QCR_BELL 0x11 #define AUTO_CAL_OFF 0x1f #define AUTO_CAL_ON 0x20 #define END_WARBLE_OFF 0x21 #define END_WARBLE_ON 0x22 #define LOAD_INTERN_LUT 0x23 #define LUT_LINEAR 1 /* Canned luts */ #define LUT_Polaroid59 2 #define LUT_Ektachrome100 3 #define LUT_Ektachrome100_4K 4 #define LUT_Polaroid59_4K 5 #define LUT_Polaroid809_4K 6 #define EXTENDED_STATUS 0x24 #define MODULE_ID 0x25 #define START_CAL 0x26 #define START_CAL_ALL 0x27 #define SHUTTER_CLOSE 0x1a #define SHUTTER_OPEN 0x1b #define BLACK_JUMP_OFF 0x28 #define BLACK_JUMP_ON 0x29 #define RESOLUTION_2K 0x2a #define RESOLUTION_4K 0x2b #define GET_BRIGHTNESS 0x2c #define SET_BRIGHTNESS 0x2d #define ROTATE_90_OFF 0x2e #define ROTATE_90_ON 0x2f #define RETURN_BRIGHT_LEVELS 0x2c #define LOAD_BRIGHT_LEVELS 0x2d #define RETURN_BRIGHT_TABLE 0x3b #define LOAD_BRIGHT_TABLE 0x3a /* Special for QCR-Z */ #define RETURN_STATUS 0x3c #define SET_FRAME_COUNTER 0x3d #define GET_FRAME_COUNTER 0x3e #define RES_2K_SAME_STATUS 0x3f #define RES_4K_SAME_STATUS 0x40 #define REWIND_FILM 0x41 #define ADVANCE_FILM 0x42 #define MULT_RGB_LUTS 0x43 #define MULT_GRAY_LUTS 0x44 #define LOAD_FILM 0x45 #define UNLOAD_FILM 0x46 #define NOTCH_FILM 0x47 #define DISABLE_HALF_FRAME 0x48 #define ENABLE_HALF_FRAME 0x49 #define DISABLE_180_ROTATE 0x4a #define ENABLE_180_ROTATE 0x4b
These are the contents of the former NiCE NeXT User Group NeXTSTEP/OpenStep software archive, currently hosted by Netfuture.ch.