This is s2r10c06.txt in view mode; [Download] [Up]
6. SCSI Commands and Status
This section defines the SCSI command and status structures and gives
several examples.
By keeping to a minimum the functions essential to communicate via this
protocol, a wide range of peripheral devices of varying capability can operate
in the same environment. Because subsets of the full architecture may be
implemented, optional functions are noted.
6.1. Command Implementation Requirements
The first byte of all SCSI commands shall contain an operation code as
defined in this standard. Targets shall implement all commands with a
mandatory operation code (see 6.1.2) both in section 7 and in the appropriate
section for their device type.
6.1.1. Reserved
Reserved bits, fields, bytes, and code values are set aside for future
standardization. Their use and interpretation may be specified by future
extensions to this standard. A reserved bit, field, or byte shall be set to
zero, or in accordance with a future extension to this standard. A target
that receives a reserved bit, field, or byte that is not zero or receives a
reserved code value shall terminate the command with CHECK CONDITION status
and the sense key shall be set to ILLEGAL REQUEST. It shall also be
acceptable for a target to interpret a bit, field, byte, or code value in
accordance with a future extension to this standard.
6.1.2. Operation Code Types
Operation
Code Type Description
--------- -------------------------------------------------------------------
M Mandatory - Commands so designated shall be implemented in order to
meet the minimum requirement of this standard.
O Optional - Commands so designated, if implemented, shall be
implemented as defined in this standard.
V Vendor specific - Operation codes so designated are available for
vendor defined commands. See the vendor specifications where
compatibility is desired.
R Reserved - Operation codes so designated shall not be used. They
are reserved for future extensions to this standard.
6.2. Command Descriptor Block
A command is communicated by sending a command descriptor block to the
target. For several commands, the command descriptor block is accompanied by
a list of parameters sent during the DATA OUT phase. See the specific
commands for detailed information.
The command descriptor block always has an operation code as its first byte
and a control byte as its last byte.
For all commands, if there is an invalid parameter in the command descriptor
block, then the target shall terminate the command without altering the
medium.
Table 6-1: Typical Command Descriptor Block for Six-byte Commands
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
Byte | | | | | | | | |
==============================================================================
0 | Operation Code |
-----|-----------------------------------------------------------------------|
1 | Logical Unit Number | (MSB) |
-----|------------------------------ ---|
2 | Logical Block Address (if required) |
-----|--- ---|
3 | (LSB) |
-----|-----------------------------------------------------------------------|
| Transfer Length (if required) |
4 | Parameter List Length (if required) |
| Allocation Length (if required) |
-----|-----------------------------------------------------------------------|
5 | Control |
==============================================================================
Table 6-2: Typical Command Descriptor Block for Ten-byte Commands
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
Byte | | | | | | | | |
==============================================================================
0 | Operation Code |
-----|-----------------------------------------------------------------------|
1 | Logical Unit Number | Reserved |
-----|-----------------------------------------------------------------------|
2 | (MSB) |
-----|--- ---|
3 | |
-----|--- Logical Block Address (if required) ---|
4 | |
-----|--- ---|
5 | (LSB) |
-----|-----------------------------------------------------------------------|
6 | Reserved |
-----|-----------------------------------------------------------------------|
7 | (MSB) Transfer Length (if required) |
-----|--- Parameter List Length (if required) ---|
8 | Allocation Length (if required) (LSB) |
-----|-----------------------------------------------------------------------|
9 | Control |
==============================================================================
Table 6-3: Typical Command Descriptor Block for Twelve-byte Commands
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
Byte | | | | | | | | |
==============================================================================
0 | Operation Code |
-----|-----------------------------------------------------------------------|
1 | Logical Unit Number | Reserved |
-----|-----------------------------------------------------------------------|
2 | (MSB) |
-----|--- ---|
3 | |
-----|--- Logical Block Address (if required) ---|
4 | |
-----|--- ---|
5 | (LSB) |
-----|-----------------------------------------------------------------------|
6 | (MSB) |
-----|--- ---|
7 | Transfer Length (if required) |
-----|--- Parameter List Length (if required) ---|
8 | Allocation Length (if required) |
-----|--- ---|
9 | (LSB) |
-----|-----------------------------------------------------------------------|
10 | Reserved |
-----|-----------------------------------------------------------------------|
11 | Control |
==============================================================================
6.2.1. Operation Code
The operation code (Table 6-4) of the command descriptor block has a group
code field and a command code field. The three-bit group code field provides
for eight groups of command codes. The five-bit command code field provides
for thirty-two command codes in each group. Thus, a total of 256 possible
operation codes exist. Operation codes are defined in the subsequent Sections
of this document.
The group code specifies one of the following groups:
Group 0 - six-byte commands (see Table 6-1)
Group 1 - ten-byte commands (see Table 6-2)
Group 2 - ten-byte commands (see Table 6-2)
Group 3 - reserved
Group 4 - reserved
Group 5 - twelve-byte commands (see Table 6-3)
Group 6 - vendor specific
Group 7 - vendor specific
Table 6-4: Operation Code
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
==============================================================================
| Group Code | Command Code |
==============================================================================
6.2.2. Logical Unit Number
The logical unit number is defined in the IDENTIFY message (5.6.7). The
target shall ignore the logical unit number specified within the command
descriptor block if an IDENTIFY message was received. It is recommended that
the logical unit number in the command descriptor block be set to zero.
NOTICE: The logical unit number field is included in the command descriptor
block for compatibility with some SCSI-1 devices. This field may be
reclaimed in SCSI-3. New implementations should use the outbound IDENTIFY
message, which is mandatory in SCSI-2, to establish the I_T_L nexus.
6.2.3. Logical Block Address
The logical block address on logical units or within a partition on device
volumes shall begin with block zero and be contiguous up to the last logical
block on that logical unit or within that partition.
A six-byte command descriptor block contains a 21-bit logical block address.
The ten-byte and the twelve-byte command descriptor blocks contain 32-bit
logical block addresses. Logical block addresses in additional parameter data
have their length specified for each occurrence. See the specific command
descriptions.
6.2.4. Transfer Length
The transfer length field specifies the amount of data to be transferred,
usually the number of blocks. For several commands the transfer length
indicates the requested number of bytes to be sent as defined in the command
description. For these commands the transfer length field may be identified
by a different name. See the following descriptions and the individual
command descriptions for further information.
Commands that use one byte for the transfer length allow up to 256 blocks of
data to be transferred by one command. A transfer length value of 1 to 255
indicates the number of blocks that shall be transferred. A value of zero
indicates 256 blocks.
In commands that use multiple bytes for the transfer length, a transfer
length of zero indicates that no data transfer shall take place. A value of
one or greater indicates the number of blocks that shall be transferred.
Refer to the specific command description for further information.
6.2.5. Parameter List Length
The parameter list length is used to specify the number of bytes sent during
the DATA OUT phase. This field is typically used in command descriptor blocks
for parameters that are sent to a target (e.g., mode parameters, diagnostic
parameters, log parameters, etc.). A parameter length of zero indicates that
no data shall be transferred. This condition shall not be considered as an
error.
6.2.6. Allocation Length
The allocation length field specifies the maximum number of bytes that an
initiator has allocated for returned data. An allocation length of zero
indicates that no data shall be transferred. This condition shall not be
considered as an error. The target shall terminate the DATA IN phase when
allocation length bytes have been transferred or when all available data have
been transferred to the initiator, whichever is less.
The allocation length is used to limit the maximum amount of data (e.g.,
sense data, mode data, log data, diagnostic data, etc.) returned to an
initiator.
6.2.7. Control Field
The control field is the last byte of every command descriptor block. The
control field is defined in Table 6-5.
Table 6-5: Control Field
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
==============================================================================
| Vendor specific | Reserved | Flag | Link |
==============================================================================
The flag bit specifies which message the target shall return to the
initiator if the link bit is one and the command completes without error.
Implementation of the flag bit is optional.
The flag bit should be set to zero if the link bit is zero. If link bit is
zero and the flag bit is one, the target shall return CHECK CONDITION status.
The sense key shall be set to ILLEGAL REQUEST.
If the flag bit is zero and the link bit is one, and if the command
completes successfully, the target shall send the LINKED COMMAND COMPLETE
message. If the flag bit is one and the link bit is one, and if the command
completes successfully, the target shall send the LINKED COMMAND COMPLETE
(WITH FLAG) message.
IMPLEMENTORS NOTE: The flag bit is typically used to cause an interrupt in
the initiator between linked commands.
The link bit is used to continue the I/O process across multiple commands.
Implementation of the link bit is optional.
A link bit of one indicates that the initiator requests a continuation of
the I/O process and that the target should enter the command phase upon
successful completion of the current command.
If the link bit is one, and if the command completes successfully, the
target shall return INTERMEDIATE or INTERMEDIATE-CONDITION MET status and
shall then send one of the two messages defined by the flag bit.
If either of the link and flag bits are set to one, and the target does not
implement linked commands, it shall return CHECK CONDITION status. The sense
key shall be set to ILLEGAL REQUEST.
6.3. Status
The status byte and status byte code are specified in Tables 6-6 and 6-7. A
status byte shall be sent from the target to the initiator during the STATUS
phase at the completion of each command unless the command is terminated by
one of the following events:
(1) an ABORT message
(2) an ABORT TAG message
(3) a BUS DEVICE RESET message
(4) a CLEAR QUEUE message
(5) a hard reset condition
(6) an unexpected disconnect (see 5.1.1)
The STATUS phase normally occurs at the end of a command but in some case
may occur prior to transferring the command descriptor block.
Table 6-6: Status Byte
==============================================================================
Bit| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
==============================================================================
| Reserved | Status Byte Code |Reserved|
==============================================================================
Table 6-7: Status Byte Code
==============================================================================
Bits of Status Byte
-----------------------------
7 6 5 4 3 2 1 0 Status
------------------------------------------------------------------------------
R R 0 0 0 0 0 R GOOD
R R 0 0 0 0 1 R CHECK CONDITION
R R 0 0 0 1 0 R CONDITION MET
R R 0 0 1 0 0 R BUSY
R R 0 1 0 0 0 R INTERMEDIATE
R R 0 1 0 1 0 R INTERMEDIATE-CONDITION MET
R R 0 1 1 0 0 R RESERVATION CONFLICT
R R 1 0 0 0 1 R COMMAND TERMINATED
R R 1 0 1 0 0 R QUEUE FULL
All Other Codes Reserved
==============================================================================
Key: R - Reserved bit
A definition of the status byte codes is given below.
GOOD. This status indicates that the target has successfully completed the
command.
CHECK CONDITION. This status indicates that a contingent allegiance
condition has occurred (see 6.6).
CONDITION MET. This status or INTERMEDIATE-CONDITION MET is returned
whenever the requested operation is satisfied (see the SEARCH DATA and PRE-
FETCH commands).
BUSY. This status indicates that the target is busy. This status shall be
returned whenever a target is unable to accept a command from an otherwise
acceptable initiator (i.e., no reservation conflicts). The recommended
initiator recovery action is to issue the command again at a later time.
INTERMEDIATE. This status or INTERMEDIATE-CONDITION MET shall be returned
for every successfully completed command in a series of linked commands
(except the last command), unless the command is terminated with CHECK
CONDITION, RESERVATION CONFLICT, or COMMAND TERMINATED status. If
INTERMEDIATE or INTERMEDIATE-CONDITION MET status is not returned, the series
of linked commands is terminated and the I/O process is ended.
INTERMEDIATE-CONDITION MET. This status is the combination of the CONDITION
MET and INTERMEDIATE statuses.
RESERVATION CONFLICT. This status shall be returned whenever an initiator
attempts to access a logical unit or an extent within a logical unit that is
reserved with a conflicting reservation type for another SCSI device (see the
RESERVE and RESERVE UNIT commands). The recommended initiator recovery action
is to issue the command again at a later time.
COMMAND TERMINATED. This status shall be returned whenever the target
terminates the current I/O process after receiving a TERMINATE I/O PROCESS
message (see 5.6.22). This status also indicates that a contingent allegiance
condition has occurred (see 6.6).
QUEUE FULL. This status shall be implemented if tagged queuing is
implemented. This status is returned when a SIMPLE QUEUE TAG, ORDERED QUEUE
TAG, or HEAD OF QUEUE TAG message is received and the command queue is full.
The I/O process is not placed in the command queue.
6.4. Command Examples
The following sections give examples of typical command processing in the
SCSI environment.
6.4.1. Single Command Example
An I/O process containing one untagged READ command is used in this section
to illustrate a simple I/O process on the SCSI bus. This example does not
include error or exception conditions.
The initiator has one set of active pointers that includes a command
pointer, a data pointer, and a status pointer. In addition, the initiator has
one set of saved pointers for each I/O process that it is able to concurrently
manage. The initiator sets up the saved pointers to point to the appropriate
bytes for the I/O process and copies the saved pointers to the active
pointers. It then arbitrates for the SCSI bus, and upon winning arbitration,
selects the target. Once the target is selected, the target assumes control
of the I/O process.
During the SELECTION phase, the initiator asserts the ATN signal to inform
the target that the initiator wishes to send a message. The target enters the
MESSAGE OUT phase and transfers the IDENTIFY message from the initiator. This
message informs the target of which logical unit is to be used. At this
point, an I_T_L nexus has been established for the I/O process. This nexus
associates the initiator's pointers with the I/O process.
The target switches to the COMMAND phase and transfers the command
descriptor block from the initiator. In this case, the command descriptor
block contains a READ command. The target interprets the command and switches
to the DATA IN phase, transfers the data, switches to STATUS phase, sends GOOD
status, switches to MESSAGE IN phase, and transfers a COMMAND COMPLETE
message. After successfully sending the COMMAND COMPLETE message, the target
goes to the BUS FREE phase by releasing the BSY signal and the I/O process
ends.
6.4.2. Disconnect Example
In the above single command example, the length of time necessary to obtain
the data may require a time-consuming physical positioning operation. In
order to improve system throughput, the target may disconnect from the
initiator, thereby freeing the SCSI bus to allow other I/O process to occur.
After the target has received the READ command (and has determined that
there will be a delay), it disconnects from the SCSI bus by sending a
DISCONNECT message and by going to the BUS FREE phase.
After the target retrieves the requested data from the peripheral device it
arbitrates for the SCSI bus. Upon winning arbitration, it reselects the
initiator and sends an IDENTIFY message to the initiator via the MESSAGE IN
phase. This revives the I_T_L nexus so that the initiator can retrieve the
correct set of pointers for the I/O process. The initiator restores the
active pointers to their most recent saved values (which, in this case, are
the initial values) and the target continues (as in the single command
example) to finish the I/O process.
If target wishes to disconnect after transferring part of the data (e.g.,
while crossing a cylinder boundary), it may do so by sending a SAVE DATA
POINTER message and a DISCONNECT message to the initiator and then
disconnecting. When reconnection is completed, the current data pointer is
restored to its value immediately prior to the SAVE DATA POINTER message.
On those occasions when an error or exception condition occurs and the
target elects to repeat the information transfer, the target may repeat the
transfer by either issuing a RESTORE POINTERS message or by disconnecting
without issuing a SAVE DATA POINTER message. When reconnection is completed,
the most recent saved pointer values are restored.
6.4.3. Linked Command Example
An I/O process may contain multiple commands "linked" together. Upon
completing a linked command successfully, the target automatically proceeds to
the next linked command for the I/O process. All commands in a series of
linked commands are addressed to the same nexus and are part of a single I/O
process.
The commands are not entirely independent. When using the relative address
bit (see 8.1.10), the address of the last logical block accessed by one of the
commands is available to the next command. Thus one can search for a
particular data pattern using a SEARCH DATA command and then read the logical
block containing the data pattern with a READ command linked to the SEARCH
DATA command. One can also read a logical block at a specified displacement
from the block containing the data pattern.
A LINKED COMMAND COMPLETE or LINKED COMMAND COMPLETE (WITH FLAG) message is
sent from the target to the initiator to indicate that a linked command
completed. The initiator then updates the saved pointers for the nexus so
that subsequent transfers from the target reference the next command of the
series. Command processing of linked and single commands is similar except
that relative addressing is permitted in linked commands.
For example, a successful completion of a SEARCH DATA EQUAL command causes
the target to continue with the linked READ command from the initiator. If
the relative address bit in the READ command has been set to one, and the
address field of the READ command is set to zero, the target transfers the
successfully searched block to the initiator.
6.5. Command Processing Considerations and Exception Conditions
The following sections describe some exception conditions and errors
associated with command processing and the sequencing of commands.
6.5.1. Programmable Operating Definition
Some applications require that the operating definition of a logical unit be
modified to meet the special requirements of a particular initiator. The
program-controlled modification of the operating definition is typically
provided to allow operating systems to change the operating definition of a
more recently developed targets to one which is more compatible with the
operating system. This ability requires that the system comply with the low-
level hardware definitions of SCSI-2.
The parameters that can be changed by modifying the operating definition of
a logical unit include the vendor identification, the device type, the device
model, the SCSI compliance level, the SCSI specification level, the command
set, and other parameters. The low-level hardware parameters including signal
timing and parity definitions cannot be changed by modifying the operating
definition. The present operating definition of a logical unit with respect
to an initiator can be determined at any time by execution of an INQUIRY
command. In some vendor-specific cases, it may also be necessary to perform
other commands including MODE SENSE and READ CAPACITY.
Each logical unit begins at a particular operating definition. If the
logical unit supports the CHANGE DEFINITION command, the present operating
definition can be changed to any other operating definition supported by the
logical unit. The actual details of the operating definition of a logical
unit are vendor-specific. If the operating definition is changed to one that
does not include the CHANGE DEFINITION command, the target should continue to
accept the CHANGE DEFINITION command.
If an error occurs during execution of a CHANGE DEFINITION command, the
original operating definition remains in effect after the command is executed.
The new operating definition becomes active only after successful execution of
the CHANGE DEFINITION command.
Since new operating definitions may preclude the execution of I/O processes
that are already in progress, the target may disconnect to allow completion of
any I/O processes that are in progress. Operating definition changes that may
cause conflicts with the normal operation from other initiators shall be
indicated to those initiators by generating a unit attention condition for
each other initiator. The additional sense code shall be set to CHANGED
OPERATING DEFINITION.
An initiator may request a list of the operating definitions that the target
supports and descriptive text for each operating definition using the INQUIRY
command.
6.5.2. Incorrect Initiator Connection
An incorrect initiator connection occurs on a reconnection if:
(1) an initiator attempts to reconnect to an I/O process, and
(2) a soft reset condition has not occurred, and
(3) the initiator does not send an ABORT, ABORT TAG, BUS DEVICE RESET, CLEAR
QUEUE, or TERMINATE I/O PROCESS message during the same MESSAGE OUT phase as
the IDENTIFY message.
An incorrect initiator connection also occurs on an initial connection when
an initiator:
(1) attempts to establish an I_T_L_Q nexus when an I_T_L nexus already
exists from a previous connection, or
(2) attempts to establish an I_T_L nexus when an I_T_L_Q nexus already
exists unless there is a contingent allegiance or extended contingent
allegiance condition present for the logical unit or target routine.
A target that detects an incorrect initiator connection shall abort all I/O
processes for the initiator on the logical unit or target routine and shall
return CHECK CONDITION status. The sense key shall be set to ABORTED COMMAND
and the additional sense code shall be set to OVERLAPPED COMMANDS ATTEMPTED.
If an initiator reconnects to an I/O process and a soft reset condition has
occurred, the target shall meet the requirements of 5.2.2.2.
IMPLEMENTORS NOTES:
(1) An incorrect initiator connection may be indicative of a serious error
and, if not detected, could result in an I/O process operating with a wrong
set of pointers. This is considered a catastrophic failure on the part of
the initiator. Therefore, vendor-specific error recovery procedures may be
required to guarantee the data integrity on the medium. The target may
return additional sense data to aid in this error recovery procedure (e.g.,
sequential-access devices may return the residue of blocks remaining to be
written or read at the time the second command was received).
(2) Some targets may not detect an incorrect initiator connection until
after the command descriptor block has been received.
6.5.3. Selection of an Invalid Logical Unit
The target's response to selection of a logical unit which is not valid is
described in the following paragraphs.
The logical unit may not be valid because:
(1) the target does not support the logical unit (e.g., some targets support
only one peripheral device). In response to an INQUIRY command the target
shall return the INQUIRY data with the peripheral qualifier set to the value
required in Table 7-16. In response to any other command except REQUEST SENSE
the target shall terminate the command with CHECK CONDITION status. In
response to a REQUEST SENSE command the target shall return sense data. The
sense key shall be set to ILLEGAL REQUEST and the additional sense code shall
be set to LOGICAL UNIT NOT SUPPORTED.
(2) the target supports the logical unit, but the peripheral device is not
currently attached to the target. In response to an INQUIRY command the
target shall return the INQUIRY data with the peripheral qualifier set to the
value required in Table 7-16. In response to any other command except REQUEST
SENSE the target shall terminate the command with CHECK CONDITION status. In
response to a REQUEST SENSE command the target shall return sense data. The
sense key shall be set to ILLEGAL REQUEST and the additional sense code shall
be set to LOGICAL UNIT NOT SUPPORTED.
(3) the target supports the logical unit and the peripheral device is
attached, but not operational. In response to an INQUIRY command the target
shall return the INQUIRY data with the peripheral qualifier set to the value
required in Table 7-16. The target's response to any command other than
INQUIRY and REQUEST SENSE is vendor specific.
(4) the target supports the logical unit but is incapable of determining if
the peripheral device is attached or is not operational when it is not ready.
In response to an INQUIRY command the target shall return the INQUIRY data
with the peripheral qualifier set to the value required in Table 7-16. In
response to a REQUEST SENSE command the target shall return the REQUEST SENSE
data with a sense key of NO SENSE unless a prior error condition exists. The
target's response to any other command is vendor specific.
6.5.4. Parameter Rounding
Certain parameters sent to a target with various commands contain a range of
values. Targets may choose to implement only selected values from this range.
When the target receives a value that it does not support, it either rejects
the command (CHECK CONDITION status with ILLEGAL REQUEST sense key) or it
rounds the value received to a supported value. The target shall reject
unsupported values unless rounding is permitted in the description of the
parameter.
Rounding of parameter values, when permitted, shall be performed as follows:
A target that receives a parameter value that is not an exact supported value
shall adjust the value to one that it supports and shall return CHECK
CONDITION status with a sense key of RECOVERED ERROR. The additional sense
code shall be set to ROUNDED PARAMETER. The initiator is responsible to issue
an appropriate command to learn what value the target has selected.
IMPLEMENTORS NOTE: Generally, the target should adjust maximum-value fields
down to the next lower supported value than the one specified by the
initiator. Minimum-value fields should be rounded up to the next higher
supported value than the one specified by the initiator. In some cases, the
type of rounding (up or down) is explicitly specified in the description of
the parameter.
6.5.5. Asynchronous Event Notification
Implementation of asynchronous event notification is optional. This
protocol can be used to inform processor devices that an asynchronous event
has occurred. A SEND command with an AEN bit of one is issued to a processor
device with a subsequent data phase that includes the REQUEST SENSE
information. SCSI devices that respond to an INQUIRY command as a processor
device type with asynchronous event notification capability may be notified of
asynchronous events using this protocol. An SCSI device has to be capable of
acting as an initiator in order to perform asynchronous event notification.
IMPLEMENTORS NOTE: Asynchronous event notification cannot be used with a
device that acts as a temporary initiator (e.g., devices executing COPY
commands) since they are not identified as a processor device.
Parameters affecting the use of asynchronous event notification are
contained in the control mode page (see 7.3.3.1).
The four uses of asynchronous event notification are:
(1) informing a processor of an error condition encountered after command
completion
(2) informing all processor devices that a newly initialized device is
available
(3) informing all processor devices of other unit attention conditions
(4) informing all processor devices of other asynchronous events.
Other uses of asynchronous event notification are not prohibited, however
this protocol is not intended to be used while an I_T_L or I_T_L_Q nexus
exists between the processor device (i.e., the initiator of the nexus) and the
other SCSI device (i.e., the target of the nexus). Asynchronous event
notification is not intended for use with target routines (i.e., an I_T_R or
I_T_R_Q nexus).
An example of the first case above is a device that implements a write
cache. If the target is unable to write cached data to the medium, it may use
an asynchronous event notification to inform the initiator of the failure. An
extended contingent allegiance condition may also be established during the
same I_T_L nexus used for the asynchronous event notification (see 5.6.9).
An example of the third case above is a device that supports removable
media. Asynchronous event notification may be used to inform an initiator of
a not-ready-to-ready transition (medium changed) or of an operator initiated
event (e.g., activating a write protect switch or activating a start or stop
switch).
An example of the fourth case above is a sequential-access device performing
a REWIND command with the immediate bit set to one. Asynchronous event
notification may be used to inform an initiator that the beginning of medium
has been reached. Completion of a CD-ROM AUDIO PLAY command started in the
immediate mode is another example of this case.
Notification of an asynchronous event is performed using the SEND command
with the AEN bit set to one. The information identifying the condition being
reported shall be returned during the DATA OUT phase of the SEND command (see
11.2.2.). The data sent is shown in Table 11-4.
An error condition or unit attention condition shall be reported once per
occurrence of the event causing it. The target may choose to use an
asynchronous event notification or to return CHECK CONDITION status on a
subsequent command, but not both. Notification of command-related error
conditions shall be sent only to the processor that initiated the I/O process.
The asynchronous event notification protocol can be used to notify processor
devices that a system resource has become available. If a target chooses to
use this method, the sense key in the sense data sent to the processor device
shall be set to UNIT ATTENTION.
The asynchronous event notification protocol shall be used only to SCSI
devices that return processor device type with an AENC bit of one in response
to an INQUIRY command. The INQUIRY command should be issued to logical unit
zero of each SCSI device responding to selection. This procedure shall be
conducted prior to the first asynchronous event notification and shall be
repeated whenever the device deems it appropriate or when an event occurs that
may invalidate the current information. (See 5.6.21, SYNCHRONOUS DATA
TRANSFER REQUEST message, for examples of these events.)
Each SCSI device that returns processor device type with an AENC bit of one
shall be issued a TEST UNIT READY command to determine that the SCSI device is
ready to receive an asynchronous event notification. An SCSI device returning
CHECK CONDITION status is issued a REQUEST SENSE command. This clears any
pending unit attention condition. An SCSI device that returns processor
device type with an AENC bit of one and returns GOOD status when issued a TEST
UNIT READY command shall accept a SEND command with an AEN bit of one.
IMPLEMENTORS NOTE: An SCSI device which can use asynchronous event
notification at initialization time should provide means to defeat these
notifications. This can be done with a switch or jumper wire. Devices
which implement saved parameters may alternatively save the asynchronous
event notification permissions either on a per SCSI device basis or as a
system wide option. In any case, a device conducts a survey with INQUIRY
commands to be sure that the devices on the SCSI bus are appropriate
destinations for SEND commands with an AEN bit of one. (The devices on the
bus or the SCSI ID assignments may have changed.)
6.5.6. Unexpected Reselection
An unexpected reselection occurs if an SCSI device attempts to reconnect to
an I/O process for which a nexus does not exist. An SCSI device should
respond to an unexpected reselection by sending an ABORT message.
6.6. Contingent Allegiance Condition
The contingent allegiance condition shall exist following the return of
CHECK CONDITION or COMMAND TERMINATED status and may optionally exist
following an unexpected disconnect. The contingent allegiance condition shall
be preserved for the I_T_x nexus until it is cleared. The contingent
allegiance condition shall be cleared upon the generation of a hard reset
condition, or by an ABORT message, a BUS DEVICE RESET message, or any
subsequent command for the I_T_x nexus. While the contingent allegiance
condition exists the target shall preserve the sense data for the initiator.
While the contingent allegiance condition exists, if the target is unable to
maintain separate sense data, the target shall respond to any other requests
for access to the logical unit or target routine from another initiator with a
BUSY status. Execution of queued commands for the logical unit or target
routine for which the contingent allegiance condition exists shall be
suspended until the contingent allegiance condition is cleared.
6.7. Extended Contingent Allegiance Condition
Implementation of extended contingent allegiance is optional. The extended
contingent allegiance condition extends the contingent allegiance condition
for an I_T_x nexus. This condition is generated by the target sending an
INITIATE RECOVERY message to the initiator following CHECK CONDITION or
COMMAND TERMINATED status and prior to the COMMAND COMPLETE message. This
condition shall be preserved until it is cleared by a BUS DEVICE RESET
message, a RELEASE RECOVERY message, or a hard reset condition.
While the extended contingent allegiance condition exists the target shall
respond to any other request for access to the logical unit from another
initiator with BUSY status. Execution of queued commands for the logical unit
for which the extended contingent allegiance condition exists shall be
suspended until the RELEASE RECOVERY message is received by the target.
IMPLEMENTORS NOTES:
(1) It is not required to generate an extended contingent allegiance
condition for every CHECK CONDITION or COMMAND TERMINATED status that
occurs. Simple errors not requiring an extended recovery may be dealt with
by using the contingent allegiance protocol.
(2) During the existence of the extended contingent allegiance condition,
appropriate error recovery sequences may be executed. Such commands can
correct data, modify or delete queued commands, perform LOG SENSE commands
and obtain diagnostic information. Extended contingent allegiance is
recommended for error conditions that may require execution of multiple-step
error-recovery protocols without interference from other initiators.
An extended contingent allegiance condition may also be generated using an
asynchronous event notification protocol. When the event is detected, the bus
device which detected the event assumes the initiator role and transmits a
SEND command with an AEN bit of one to the appropriate device(s) (see 11.2.2).
If the device wishes to generate an extended contingent allegiance condition
during an asynchronous event notification, it shall send an INITIATE RECOVERY
message following the IDENTIFY message (and following any queue tag message)
and prior to the COMMAND phase of the SEND command. An extended contingent
allegiance condition can be generated for only one I_T_L nexus at a time. The
extended contingent allegiance condition is cleared when a RELEASE RECOVERY
message is received from the device to which the INITIATE RECOVERY message was
sent. The generation of a hard reset condition, or receipt of a BUS DEVICE
RESET message shall also clear the extended contingent allegiance condition.
During an extended contingent allegiance only untagged I/O processes from
the SCSI device to which the INITIATE RECOVERY message was sent shall be
executed by the target. If the initiator sends a queue tag message the target
shall respond with QUEUE FULL status. After the extended contingent
allegiance condition is cleared any commands remaining in the command queue
shall be executed.
6.8. Queued I/O Processes
The implementation of queuing for I/O processes is optional. Queuing of I/O
processes allows a target to accept multiple I/O processes for execution at a
later time.
There are two methods for implementation of queuing, tagged and untagged.
Tagged queuing allows a target to accept multiple I/O processes from each
initiator for each logical unit or target routine. Untagged queuing allows a
target to accept one I/O process from each initiator for each logical unit.
A target may be capable of both methods of queuing, but only one method may
be used by an initiator at a time. Other initiators may choose the other
queuing method; in that case, the target may manage both types of queued
commands.
Untagged queuing may be supported by SCSI-1 or SCSI-2 devices. Tagged
queuing is new in SCSI-2.
6.8.1. Untagged Queuing
Untagged queuing allows a target to accept a command from an initiator for a
logical unit or target routine while a command from another initiator is being
executed. Only one command for each I_T_x nexus shall be accepted at a time.
An I/O process may be initiated any time the BUS FREE phase exists even if
an I/O process from a different initiator is active. If the disconnect
privilege is not granted in the IDENTIFY message of the new I/O process, the
target may either suspend the active I/O process or it may return BUSY status
to the new I/O process.
The I_T_x nexus sufficiently specifies the relationship so that the target
can reconnect to the initiator to restore the pointers for I/O process as long
as only one I/O process per I_T_x nexus is issued. It is the responsibility
of the initiator to assure that only one such I/O process is issued at any
time (see 6.5.2).
6.8.2. Tagged Queuing
Tagged queuing allows a target to accept multiple I/O processes from the
same or different initiators until the logical unit's command queue is full.
If an I/O process is received and the command queue is full, the target shall
terminate the I/O process with QUEUE FULL status.
The command queue is setup by the target for each supported logical unit and
target routine. Initiators may add or delete I/O processes to the queue.
When adding an I/O process, the initiator may specify fixed order of
execution, allow the target to define the order of execution, or specify that
the I/O process is to be executed next.
If the disconnect privilege is not granted in the IDENTIFY message for a
tagged I/O process the target shall return BUSY status.
The queue tag messages (see 5.6.17) allow the initiator to establish a
unique I_T_L_Q nexus to identify each I/O process. The I_T_L_Q nexus allows
the target to reconnect to a specific I/O process and allows the initiator to
restore the set of pointers for that I/O process. An initiator may have
several I/O processes ongoing to the same or different logical units or target
routines as long as each has a unique nexus.
If only SIMPLE QUEUE TAG messages are used, the target may execute the
commands in any order that is deemed desirable within the constraints of the
queue management algorithm specified in the control mode page (see 7.3.3.1).
If ORDERED QUEUE TAG messages are used, the target shall execute the
commands in the order received with respect to other commands received with
ORDERED QUEUE TAG messages. All commands received with an SIMPLE QUEUE TAG
message prior to a command received with an ORDERED QUEUE TAG message,
regardless of initiator, shall be executed before that command with the
ORDERED QUEUE TAG message. All commands received with an SIMPLE QUEUE TAG
message after a command received with an ORDERED QUEUE TAG message, regardless
of initiator, shall be executed after that command with the ORDERED QUEUE TAG
message.
A command received with a HEAD OF QUEUE TAG message is placed first in the
queue, to be executed next. A command received with a HEAD OF QUEUE TAG
message shall not suspend an I/O process for which the target has begun
execution. Consecutive commands received with HEAD OF QUEUE TAG messages are
executed in a last-in-first-out order.
An I/O process received without a queue tag message while there are any
tagged I/O commands in the command queue from the same initiator is an
incorrect initiator connection (see 6.5.2) unless there is a contingent
allegiance or extended contingent allegiance condition.
A series of linked commands are a single I/O process, and are assigned the
queue tag established in the initial connection. A command received with a
HEAD OF QUEUE TAG message shall not suspend a series of linked commands for
which the target has begun execution.
The RESERVE and RELEASE commands should be sent with an ORDERED QUEUE TAG
message. Use of the HEAD OF QUEUE TAG message with these commands could
result in reservation conflicts with previously issued commands.
The TEST UNIT READY and INQUIRY commands are often sent with a HEAD OF QUEUE
TAG message, since the information returned has no effect on the condition of
the logical unit.
Two error recovery options are allowed. The error recovery option to be
used is specified in the control mode page (see 7.3.3.1).
The first post-recovery option is to continue execution of commands in the
queue after the contingent allegiance or extended contingent allegiance
condition has cleared. The target returns BUSY status to other initiators
while the contingent allegiance or extended contingent allegiance condition
exists. During this time all commands in the queue are suspended. All
commands used for recovery operations shall be untagged commands. The queue
may be modified by removing all or selected commands in the queue as part of
the recovery procedure.
If commands are combined by the queuing algorithm such that the error
affects more than one command, then a contingent allegiance condition shall be
generated for all affected commands.
The second recovery option clears the queue after the contingent allegiance
or extended contingent allegiance condition has been cleared. When the queue
is cleared because of this recovery option, a unit attention condition shall
be generated for all other initiators and the additional sense code shall be
set to COMMANDS CLEARED BY ANOTHER INITIATOR.
Deferred errors are normally related to a command that has already
completed. As such, there is no attempt to return the queue tag value
assigned to the original command.
A device that does not support tagged queuing for any reason (e.g., not
implemented, disabled by the DQue bit in the control mode page, or it has been
switched to an operating definition that does not include tagged queuing)
shall respond to any queue tag message with a MESSAGE REJECT message. The
target shall continue the I/O process as if it was an untagged I/O process.
Tagged queuing may also be temporarily disabled internal to the SCSI device
during certain initialization periods or to control internal resource
utilization. During these periods the target may elect to return QUEUE FULL
status or it may respond to any queue tag message with a MESSAGE REJECT
message.
Several messages may be used to clear part or all of the command queue.
Please refer to the ABORT, ABORT TAG, BUS DEVICE RESET, and CLEAR QUEUE
messages in Section 5 for details.
6.8.3. Example of Queued I/O Process
An example of I/O process queuing benefits from the consideration of the
execution of a number of commands. After each command, the state of the queue
kept in the target is shown to indicate the function actually performed by the
queuing.
6.8.3.1. Typical Sequences for Tagged Queuing
An I/O process using tagged queuing uses the following sequences for normal
execution. The initiator first arbitrates for the SCSI bus, and after
successfully obtaining the SCSI bus, selects the appropriate SCSI device. The
ATN signal is asserted during the SELECTION phase to indicate that a MESSAGE
OUT phase is requested by the initiator. The first message byte transferred
is an IDENTIFY message. The ATN signal continues to be asserted during the
MESSAGE OUT phase to indicate that the initiator has another message. The
second message byte transferred is the first byte of the appropriate queue tag
message, in this case a SIMPLE QUEUE TAG message. The third and last message
byte is transmitted containing the second byte of the queue tag message, the
queue tag. As it is transferred, the ATN signal is negated to indicate that
no more message bytes are available. The target then transfers the command
descriptor block. Assuming the command requires disconnection, the target
transmits a DISCONNECT message to the initiator and then enters the BUS FREE
phase. The target places the command, identified by the I_T_L_Q nexus, at the
appropriate place in the command queue.
When the target removes I/O processes from the queue for execution, a
physical latency period may occur. At the end of this period, when the target
is prepared to transfer the appropriate data, the target begins an ARBITRATION
phase and, upon winning, enters a RESELECTION phase. After a successful
reselection, the target sends the IDENTIFY message followed by a SIMPLE QUEUE
TAG message with the queue tag value originally sent by the initiator. The
initiator uses the I_T_L_Q nexus to identify the correct set of pointers and
control blocks associated with the I/O process and to establish the necessary
conditions for data transfer. The target begins data transfer. When the data
transfer is successfully completed, the target returns GOOD status and
terminates the I/O process with a COMMAND COMPLETE message.
6.8.3.2. Example of Tagged Queuing
An example of the execution of five queued I/O processes is described to
demonstrate how tagged queuing operates. All tagged I/O processes are from
one initiator to a single logical unit of a single target. The five I/O
processes are defined in Table 6-8. The target is a direct-access device. At
the time the I/O processes are first being executed, it is assumed that the
actuator is in position to access logical block 10000.
Table 6-8: Commands in Order Received by Target
Queue Logical
Tag Block Transfer
Command Queue Tag Message Value Address Length Status
------- ----------------- ----- ------- --------- ---------
READ SIMPLE 01h 10000 1000 Queued
READ SIMPLE 02h 100 1 Queued
READ ORDERED 03h 1000 1000 Queued
READ SIMPLE 04h 10000 1 Queued
READ SIMPLE 05h 2000 1000 Queued
The optimum order would require that those blocks close to the actuator
position be the first blocks accessed, followed by those increasingly far from
the actuator position. However, the command with queue tag 03h is an ordered
I/O process, so that all simple I/O processes transferred previously must be
executed before, while all simple I/O processes transferred after the ordered
I/O process must be executed after the ordered I/O process.
If a target supports an optimizing algorithm the actual order in which the
I/O processes are executed could be as shown in Table 6-9.
Table 6-9: Commands in Order of Execution
Queue Logical
Tag Block Transfer
Command Queue Tag Message Value Address Length Status
------- ----------------- ----- ------- --------- ---------
READ SIMPLE 01h 10000 1000 Queued
READ SIMPLE 02h 100 1 Queued
READ ORDERED 03h 1000 1000 Queued
READ SIMPLE 05h 2000 1000 Queued
READ SIMPLE 04h 10000 1 Queued
I/O processes with queue tag values 01h and 02h are executed in the order
received since the actuator is already in position to execute I/O process 01h.
I/O process 02h must be executed before I/O process 04h or 05h because the
ordered I/O process 03h was transmitted after I/O processes 01h and 02h but
before I/O processes 04h and 05h. I/O process 03h is then executed after I/O
process 02h. The I/O processes 04h and 05h are executed after the ordered I/O
process 03h. I/O process 05h is executed before I/O process 04h because the
actuator is in position to access block 2000 after executing I/O process 03h.
I/O process 04h is executed last.
As an example of the operation of the HEAD OF QUEUE TAG I/O process,
consider that a new I/O process, identified by a HEAD OF QUEUE TAG message
with a queue tag of 08h, is transmitted to the target while the ordered I/O
process 03h is being executed. The I/O process 03h continues execution, but
the new HEAD OF QUEUE TAG I/O process is placed in the queue for execution
before all subsequent I/O processes. In this case, the queue for execution
after the ordered I/O process 03h was executed would appear as shown in Table
6-10.
Table 6-10: Modified by HEAD OF QUEUE TAG Message
Queue Logical
Tag Block Transfer
Command Queue Tag Message Value Address Length Status
------- ----------------- ----- ------- --------- ---------
READ ORDERED 03h 1000 1000 Executing
READ HEAD OF QUEUE 08h 0 8 Queued
READ SIMPLE 05h 2000 1000 Queued
READ SIMPLE 04h 10000 1 Queued
To obtain maximum performance gains using tagged queuing requires careful
implementation of the queuing algorithms in the target. In addition,
initiators should allow a maximum number of simple I/O processes to be
executed with a minimum number of ordered I/O processes. RESERVE and RELEASE
commands, SET LIMITS commands, and appropriate software locking conventions
should be used to guarantee the proper relationship between the commands
executed and the data stored on the peripheral devices. These conventions are
not defined by this standard.
6.9. Unit Attention Condition
The target shall generate a unit attention condition for each initiator on
each valid logical unit whenever the target has been reset by a BUS DEVICE
RESET message, a hard reset condition, or by a power-on reset. The target
shall also generate a unit attention condition on the affected logical unit(s)
for each initiator whenever one of the following events occurs:
(1) A removable medium may have been changed.
(2) The mode parameters in effect for this initiator have been changed by
another initiator.
(3) The version or level of microcode has been changed.
(4) Tagged commands queued for this initiator were cleared by another
initiator.
(5) INQUIRY data has been changed.
(6) The mode parameters in effect for this initiator have been restored from
non-volatile memory.
(7) A change in the condition of a synchronized spindle.
(8) Any other event occurs that requires the attention of the initiator.
IMPLEMENTORS NOTES:
(1) Targets may queue unit attention conditions on logical units. After
the first unit attention condition is cleared, another unit attention
condition may exist (e.g., a power on condition followed by a microcode
change condition). The initiator can clear all pending unit attention
conditions by repeatedly sending the REQUEST SENSE command until a sense key
other than UNIT ATTENTION is returned by the target.
(2) See 6.5.3 for requirements concerning selection of an invalid logical
unit.
The unit attention condition shall persist on the logical unit for each
initiator until that initiator clears the condition as described in the
following paragraphs.
If an INQUIRY command is received from an initiator to a logical unit with a
pending unit attention condition (before the target generates the contingent
allegiance condition), the target shall perform the INQUIRY command and shall
not clear the unit attention condition. If the INQUIRY command is received
after the target has generated the contingent allegiance condition for a
pending unit attention condition, then the unit attention condition on the
logical unit shall be cleared, and the target shall perform the INQUIRY
command.
If any other command is received after the target has generated the
contingent allegiance condition for a pending unit attention condition, the
unit attention condition on the logical unit shall be cleared, and if no other
unit attention condition is pending the target shall perform the command. If
another unit attention condition is pending the target shall not perform the
command and shall generate another contingent allegiance condition.
If a REQUEST SENSE command is received from an initiator with a pending unit
attention condition (before the target generates the contingent allegiance
condition), then the target may either:
(1) report any pending sense data and preserve the unit attention condition
on the logical unit or
(2) report the unit attention condition, may discard any pending sense data,
and clear the unit attention condition on the logical unit for that initiator.
If the target has already generated the contingent allegiance condition for
the unit attention condition, the target shall perform the second action
listed above.
If an initiator issues a command other than INQUIRY or REQUEST SENSE while a
unit attention condition exists for that initiator (prior to generating the
contingent allegiance condition for the unit attention condition), the target
shall not perform the command and shall report CHECK CONDITION status unless a
higher priority status as defined by the target is also pending (e.g., BUSY or
RESERVATION CONFLICT).
If after generating the contingent allegiance condition for a pending unit
attention condition, the next command received from that initiator on the
logical unit is not REQUEST SENSE, then that command shall be performed and
the unit attention condition shall be cleared for that initiator on the
logical unit and the sense data is lost (see 6.6).
If a target becomes a temporary initiator to issue a SEND command with an
AEN bit of one, which informs the initiator (temporary target) of the unit
attention condition, and the SEND command completes with GOOD status, then the
target shall clear the unit attention condition for that initiator on the
logical unit (see 6.5.5).
(This page is intentionally blank.)
These are the contents of the former NiCE NeXT User Group NeXTSTEP/OpenStep software archive, currently hosted by Netfuture.ch.